夯錘泵連接盤#D-48407RHEINE#171600

夯錘的工作原理：夯錘由偏心軸驅動，實現上下運動，從而壓緊熨平板下方的材料。為了獲得更高的預壓實度，應該根據特定的層厚和攤鋪速度正確的設置夯錘。

福格勒攤鋪機夯錘調節比例為：根據1米每分鐘夯錘的轉速同步增加。夯錘的轉速隨攤鋪速度的加大而加大，一般進行瀝青攤鋪時，起步時夯錘轉速的設定：底層選擇10%（攤鋪厚度8-10公分）中面層攤鋪選擇6%（4-6公分），根據試驗段的結果確定最終的起步速度的設定，然后根據1米每分鐘夯錘的轉速同步增加，在同批次材料攤鋪中，攤鋪速度與夯錘的比例不能隨意修改。

 

免責聲明丨 部分內容來源網絡！本文僅供交流學習 , 版權歸屬原作者，部分圖片、內容推送時未能及時與原作者取得聯系，若來源標注錯誤或侵犯到您的權益煩請告知，我們將立即刪除.

企業介紹

公司供應攤鋪機配件，壓路機配件，銑刨機配件，攤鋪機刮板驅動軸，刮板驅動軸總成，找平儀，找平儀支架以及液壓泵和配件。我廠還供應攤鋪機易損件，攤鋪機平衡梁，攪龍軸，踏板，輸料底板，葉片，熨平板，減速機，鏈軌，履帶板，支重輪，刮板大鏈條，輸料鏈條等。

 

聯系人：梁經理

聯系方式：13645201509（微信同號）

 

QQ：2870202745

Working principle of rammer: driven by eccentric shaft, the rammer can move up and down to compress the material under the screed. In order to obtain a higher degree of precompaction, the rammer should be set correctly according to the specific layer thickness and paving speed.

 

The adjustment ratio of the hammer of Fogler paver is: increase synchronously according to the speed of the hammer per minute. The speed of the rammer increases with the increase of the paving speed. Generally, when paving asphalt, the setting of the speed of the rammer at the start: 10% (paving thickness 8-10 cm) for the bottom layer and 6% (4-6 cm) for the middle layer paving. The final setting of the starting speed is determined according to the results of the test section, and then the speed of the rammer at 1 meter per minute increases synchronously. In the same batch of material paving, the proportion of the paving speed and the rammer cannot be arbitrarily modified.

 

Disclaimer | Part of the content comes from the network! This article is only for exchange and learning. The copyright belongs to the original author. Some pictures and content are not timely contacted with the original author when being pushed. If the source label is incorrect or infringes your rights and interests, please inform us and we will delete it immediately

 

Enterprise introduction

 

The company supplies paver parts, roller parts, milling machine parts, paver scraper drive shaft, scraper drive shaft assembly, leveling instrument, leveling instrument support, hydraulic pump and accessories. Our factory also supplies vulnerable parts of pavers, paver balance beams, auger shafts, pedals, feeding soleplates, blades, screeds, reducers, chain tracks, track shoes, rollers, scraper large chains, feeding chains, etc.

 

Contact: Manager Liang

 

Contact: 13645201509 (WeChat same number)

QQ：2870202745